Home » Design Examples  

Steel Wall Systems Manual

General information/ Warranty and design considerations
Engineering design certification
Certification, standards and testing
Performance
Technical services
Fire and acoustic rated systems

Peer Steel Wall Products
Partition or wall studs and track
Deflection head and noggin track
Accessories for acoustic applications
Top hats
Plaster accessories

Partition and wall framing – installation
Bottom track fixing detail
Top (Head) track fixing detail
Top (Head) track fixing detail – suspended ceiling
Deflection head track fixing detail
Fixing methods explained
Plasterboard installation
Control joints explained
Storage and Handling
Table SWS-01 - Wall Lipped Studs
Table SWS-02 - Wall Lipped Studs
Table SWS-03 - Top Hats
Table SWS-04 - Top Hats
Design notes and sectional properties
WSL design examples
Top Hat design examples
Sectional properties SWS-05
Sectional properties SWS-06
Sectional properties SWS-07
Sectional properties SWS-08
Sectional properties SWS-09
Sectional properties SWS-10
Sectional properties SWS-11
Sectional properties SWS-12
Sectional properties SWS-13
Sectional properties SWS-14
Sectional properties SWS-15

Peer Facade System Manual

General / Design & Warranty Information
Engineering design certification
Certification, standards and testing
Performance
Technical services

Peer Façade system Products
Façade system Backing Strip
Top Hat 50, 120 and EPDM foam seal
Façade EPDM seal characteristics
Panel Layout and Top Hat spacing
Top Hat levelling and fixing – EPDM Foam seal application
Pre mark and drill boards prior to fixing
Backing Strip as a vertical spacer and sealant application
Insertion of backing strip and overlapping seal details
Backing strip overlapping seal and prep for Top board
Fixing to layer of boards and prep screw holes for filling
Finish façade joint sealing & Control Joints
Control Joints
Storage, Handling & Design Capacities
Section properties TH120
Section properties TH75 & TH50
Span table maximum wind pressure

Concealed Ceiling systems Manual

General / Design & Warranty Information
Engineering design certification
Technical services
Certification, standards and testing
Performance

PEER Concealed Ceiling Steel
Product Breakdown
Furring channel
Top cross rail
Clips
Miscellaneous components
Acoustic application accessories
Top hats
Ceiling battens
Ceiling joists
Concealed ceiling systems install
Typical suspended ceiling with TCR/FC
Direct fixing of furring channels
Drop ceiling/ceiling bulkhead
Fire rated ceilings
Acoustic STC rated ceilings
Typical concealed ceiling joists
Curven and raked ceilings
Plasterboard installation
Expansions and control joints

Design notes
Span table CCS01
Span table CCS02
Span table CCS03
Span table CCS04
Span table CCS05
Span table CCS06
Span table CCS07
Clip Capacity Table CCS08
Sectional properties SP-01
Sectional properties SP-02
Sectional properties SP-03
Sectional properties SP-04
Sectional properties SP-05

Exposed Grid system Manual

General / Design & Warranty Information
Engineering design certification
Certification, standards and testing
Technical services

PEER Exposed Grid Ceiling
Simplicitee components
Simplicitee components details
Two way exposed grid
One way linear grid
Raked ceiling detail
Light fitting detail

Installation details
Two way exposed grid
Part tile lengths/widths
Wall angle trim fixing
Suspension rod fixing
Main/Cross runner suspension clips
Main runner to wall angle junction
Detail at light fitting
Main runner to wall angle junction
Maximum load Table EGS01
Clip Capacity Table EGS-02
Grid layout examples
Ceiling tiles
Sectional properties SP-01
Previous Page
Design Examples
 Next Page

TOP HATS as Façade or Fascia Frame

Maximum Girt Spacing (Maximum Span of Top Hat)

For use of Peer Top Hats on Girts/support structure etc

Example 3a
Lateral pressure = 2.0 kPa permissible or 3.0 kPa Ultimate
Number of spans - Single

Product
Top Hat spacing
Max Top Hat Span
TH75-115
600
1295
TH75-115
450
1425
TH50-115
600
1225
TH50-115
450
1350

Example 3b
Lateral pressure = 2.0 kPa permissible or 3.0 kPa Ultimate
Number of spans – Double Span

Product
Top Hat spacing
Max Top Hat Span
TH75-115
600
1485
TH75-115
450
1715
TH50-115
600
1450
TH50-115
450
1670

Example 3c
Lateral pressure = 2.0 kPa permissible or 3.0 kPa Ultimate
Number of spans - Continuous

Product
Top Hat spacing
Max Top Hat Span
TH75-115
600
1580
TH75-115
450
1760
TH50-115
600
1515
TH50-115
450
1665

Example 4a
Lateral pressure = 1.5 kPa permissible or 2.25 kPa Ultimate
Number of spans - Single

Product
Top Hat spacing
Max Top Hat Span
TH75-115
600
1425
TH75-115
450
1570
TH50-115
600
1350
TH50-115
450
1485

Example 4b
Lateral pressure = 1.5 kPa permissible or 2.25 kPa Ultimate
Number of spans - Double

Product
Top Hat spacing
Max Top Hat Span
TH75-115
600
1710
TH75-115
450
1980
TH50-115
600
1675
TH50-115
450
1930

Example 4c
Lateral pressure = 1.5 kPa permissible or 2.25 kPa Ultimate
Number of spans - Continuous

Product
Top Hat spacing
Max Top Hat Span
TH75-115
600
1760
TH75-115
450
1940
TH50-115
600
1665
TH50-115
450
1835
   PEER Industries Technical Manual Rev 05